Here’s the customer solution to help users solve the problem locked and can not read or program chip issue. This is done off board with qfp64 breakout board should be able to program onboard xprog also though. Disclaimer: Many thanks dil6222 from cartechnology.co.uk forum. You are at your risk.

Easy fix all you need is: 1. PROGRAMMER 2. USBASP WITH SLOW CLOCK JUMPER ON EXTREME BURNER SOFTWARE AND 10 TO 6PIN ADAPTER 3.

JUMPER WIRES FEMALE AND MALE 4.QFP64 BREAKOUT BOARD let’s get started 1. First of all connect jumper wires between atmega and usbasp you will need to split vcc + into 3 wires and gnd – into 3 wires Connect vcc+ to pin 21,52 and (64 i believe optional as for avcc i test later) Connect gnd- to pin 22,53 and 63 Connect SCK to SCK Connect RESET to RESET MOSI to PE0 (common problem is people using PB2 and PB3 as there listed as mosi and MISO but they are not ) MISO to PE1 You should end up with something like this.

Free Download Xprog-M V5.0, V5.3, V5.50 and V5.55 software August 12, 2015 www.ecu-programmer.com Auto ECU Programmer, XPROG-M Several versions Xprog-M ECU chip tuning programmers are available in eobdtool.co.uk.

You can see I’ve split the and vcc 2. Next connect PIN2 from DB9 SOCKET to XTAL 1. Now connect everything else usbasp and upa to usb etc Now comes the fun bit 3. Open upa software go on tools then pulse generator and you will see this: Change frequency to 1000khz and click start and leave it running.

Open extreme burner avr and go to fuse settings tab and click on read atmega should connect as normal 5. Go on each set of fuses low, high, extended lock go on bit details and click load default value for each set Then tick all the write boxs and click write.

(0) (0)| • • By: July 13, 2014 • good product en good seller • Was the review helpful to you? Digital therapy machine instrukciya na russkom. (0) (0)| • • By: June 17, 2014 • good seller and great product • Was the review helpful to you? • Was the review helpful to you?

Or you can manually enter the following ( Low E1, HIGH 99, EXTENDED FD, LOCK FF then click write these are factory lockbits. Go on low fuses and check the following clksel settings are there Cksel0 (1) Cksel1 (0) Cksel2 (0) Cksel3 (0) Now erase chip and then disconnect upa That’s it all done it should be able to program/ read as normal without upa sending signal to xtal1 on mega. Hope this helps many users to unlock atmega 64.

Description: The XPROG-M supports in-circuit and on-board programming of Motorola 68HC05, 68HC08, 68HC11, 68HC(S)12 family MCU's, Texas Instruments TMS370/TMS374 family MCU's and serial EEPROM's. Xprog-M Programmer Plus V5.3 Never Locked with USB Dongle. The latest new add to 24 adapter and Multi-Versioning of software, support chip models more. XPROG the-m Rev.

E features: Fully compatible with the Device Programmer Desktop version of the software. Software update (ATMEGA)- directly from the Device Programmer Desktop update Language: English, Chinese Support system: Windows xp, Windows 7 Xprog-M V5.3 Features: History Supreme programmer, most versatile, supporting most devices programming instrument! Real online reading and writing Motorola 912, 9S12 encryption chip and CDC series of encryption chip. Reads and writes the new Nissan, Teana BCM Anti-theft data without remove. By k-line reading the BMW EWS anti-theft computer data. All software features full opening.

Multi-function equipment: Supports most of the CPU to read and write without remove, BMW EWS3 (0D46J/2D47J) socket read and write, and read and write ordinary IC. Support Motorola 68HC05, 68HC08, 68HC11, HC912, MC9S12, MC9S12X, TMS370, K cable interface, the MPC5xx, ST10Fxx, CDC series, ATmega family MCU and all series EEPROM programming. All COM port and USB port support!